Why Do We Use A Patch Panel?

When we set up a network, we are accustomed to buying a patch panel as usual. And people always say they buy patch panels for cable management, as they are asked why do we use a patch panel. However, are there any other benefits of a patch panel? Yes, of course, here explains the reasons why do we use a patch panel in networking.

Why Use A Patch Panel?

Figure 1: Patch panels in a rack for managing the fiber and copper cables
Figure 1: Patch panels in a rack for managing the fiber and copper cables

As shown in the picture above, patch panels are usually attached in the network racks. All the cables from the individual desktop, computer or printer go to the patch panel. Then the patch panel provides protection and management for the cables, which contributes to ensuring the cables’ performance in the whole network. This is the greatest benefit of using a patch panel. Whenever cables change direction, the bending of the cables is likely to change the electrical properties. If one cable bends too far, unfortunately, damages may occur inside where you can’t see it. So patch panels can help to protect the delicate cables.

Besides, using a patch panel improves working efficiency and workflow. How? For example, telecommunication and cable companies always use patch panels in strategic locations in their coverage areas. Therefore, the technicians can connect or disconnect services to the specific places without going to the actual locations just by managing the patch panels.

Finally, using a patch panel also improves the aesthetics of your work area. All cables are in place and accessible represent a well-managed workstation, which also shows the quality.

Why Not Use A Switch Instead of Patch Panel?

When someone connects the cables, he may wonder why use a patch panel is a requirement and why they aren’t connected to network switches directly. The answer is that patch panel and the switch play different roles in the cabling system. Patch panel acts just as a connector which will not make any influences on data transmission, but a network switch connects hardware within a network to enable them to access the Internet, share data etc. In a data center rack, there are many network switches with numbers of ports. Routing cables from one rack to another is a tough job. So you have to use patch panels to manage these cables.

Fiber and Copper Patch Panels Recommendation

Designed for specific cables like Cat5e, Cat6 copper cables and OS2, OM3 fiber cables, patch panels types are different.

Fiber Optic Patch Panel
Figure 1: Patch panels in a rack for managing the fiber and copper cables
Figure 1: Patch panels in a rack for managing the fiber and copper cables

This type of patch panel takes the simplex, duplex and quad model designs at FS.COM. There are 24 port patch panel and 48 port patch panel available for you to choose. All products are produced strictly in accordance with national standards. The following is a 24 port LC duplex fiber optic patch panel used to connect 48 OS2 single mode fibers. It uses the standardized jack that makes it easy to insert and remove fiber cables so that to ensure the long-term and stable performance of the fiber cables.

Ethernet Patch Panel
Cat6 Patch Panel: used for Cat6 cable management
Cat6 Patch Panel: used for Cat6 cable management

FS.COM offers punch down and feed-through Ethernet patch panel. And the feed-through patch panel falls into unshielded and shielded types to wire the unshielded and shielded Ethernet cables. The following is a 24 port Cat6 unshielded feed-through patch panel. Design with SPCC and ABS plastics materials, the Ethernet patch panel is sturdy and durable that can work in the environment of -25°C to 70°C.

Blank Keystone Patch Panel
photo of a 48 Ports Keystone Patch Panel Cabling
Figure 2: 48 Ports Blank Keystone Patch Panel Cabling

When you are unable to decide in advance which type of cables will be used to connect your hardware, you can use a blank keystone patch panel. The following is a 48 port blank keystone patch panel that provides flexibility in the type of jacks. As a result, you can make a mixed connection based on your actual demands.

Conclusion

What is the purpose of the patch panel in networking, or why use a patch panel? I think now you have a good understanding. Today’s fast-changing technology makes more and more electrical and electronic devices connected to each other, so don’t hesitate to use a patch panel to simplify the cabling.

Author: Feisu

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.